AGD C/F frame - Crossman stock mod

Well OPBN ask the question and I was the guinea pig

https://automags.org/forums/showthrea...Will-this-work


First step was to check what was preventing the two from mating :D
as you can see they are close but material needs to be removed for the AGD frame to fit

http://i1325.photobucket.com/albums/...ps91ef6e41.jpg


i cut the back off the stock because it was in the way of the rear screw on the frame

http://i1325.photobucket.com/albums/...psa3770da4.jpg


as I refit and cleared away more material from the stock the frame became easier to insert :D

http://i1325.photobucket.com/albums/...ps83c3aca8.jpg

http://i1325.photobucket.com/albums/...psfe453564.jpg


I wanted to maintain the channel the posts on the frame ride in, but on the crossman frames the geometry is slightly different.
I took a used cutting wheel and cut the channel straight back. I used the painters tape as a guide

http://i1325.photobucket.com/albums/...psc7f9a951.jpg

http://i1325.photobucket.com/albums/...ps1104c819.jpg


i cleaned up the front and checked alignment again, and marked a spot for the new hole from stock to frame

http://i1325.photobucket.com/albums/...ps14db6480.jpg

http://i1325.photobucket.com/albums/...ps3be16ef9.jpg


using a hand file and sandpaper i cleaned up the back

http://i1325.photobucket.com/albums/...ps662796e4.jpg


Drilled and tapped the hole 10/32

http://i1325.photobucket.com/albums/...psb11ba6eb.jpg

http://i1325.photobucket.com/albums/...ps48c1554f.jpg


...and BOOM!!!

http://i1325.photobucket.com/albums/...psddcdf971.jpg

http://i1325.photobucket.com/albums/...psef72eab8.jpg

wow, 22$ WELL spent

Attachment 88550

One I did a while back a little differently. Fits on an emag frame.

How secure? Any wobble?

Quote:

---

Originally Posted by OPBN

How secure? Any wobble?

---

very secure no wobble at all. you could even put mounting screws into the bottom of the frame as well

Glad to see. And not much modding to the frame really besides a hole. Easily convertible back to stock grip. Might have to go ahead and pick one up for giggles. Thanks for the nice right up and pics for those of us that are reading challenged. lol.

Quote:

---

Originally Posted by OPBN

Glad to see. And not much modding to the frame really besides a hole. Easily convertible back to stock grip. Might have to go ahead and pick one up for giggles. Thanks for the nice right up and pics for those of us that are reading challenged. lol.

---

Always a pleasure

I like it

Always wanted one of those set up like that, wish I had the skill to finish it off like that. Great work

total cost?

$22 shipped to the wally world down the street... and a steady hand to cut it

Quote:

---

Originally Posted by rukh013

$22 shipped to the wally world down the street... and a steady hand to cut it

---

sorry, I meant time spent and misc cost.
22$ +.... ?
I was just looking to compare, I have 3 of these stock previously mod'd and done about 3 yrs back. didn't know they were that big of deal.
just comparing cost to a production stand point.
thankyou,
KNM.

it took about 30-45 min, I made sure to use tools most people have: Dremel, cutting wheel, high speed cutter, 1/2" half round bastard file, sandpaper (220 then 500) and tape as a guide

if i did it again i could do it in 10 min, there wasn't much to it. the checking the fit as i went was the most time consuming

Quote:

---

Originally Posted by rukh013

it took about 30-45 min, I made sure to use tools most people have: Dremel, cutting wheel, high speed cutter, 1/2" half round bastard file, sandpaper (220 then 500) and tape as a guide

if i did it again i could do it in 10 min, there wasn't much to it. the checking the fit as i went was the most time consuming

---

Oh good 10 mins, frame and stock in the way to ya, would have hated for it to take you longer than 20 mins

Quote:

---

Originally Posted by Mercenario

Oh good 10 mins, frame and stock in the way to ya, would have hated for it to take you longer than 20 mins

---

:)

what???

This makes me want to but a mag just to make into a rifle. Very nicely done!!

Quote:

---

Originally Posted by rukh013

:)

what???

---

Trying a jedi mind trick of sorts, need to keep practicing

WOW. I wish I had those skills when I did mine:

http://i181.photobucket.com/albums/x...8/1fc5e45c.jpg
http://i181.photobucket.com/albums/x...8/5b396795.jpg

I sawed of the bottom of my frame instead of making room for it on the stock. That's why I applied the tennis racket tape over it. Still, mine doesn't wobble either but I'd love to have preserved the frame as you did.

it works on both the crossman frame and AGD frames, tested it this weekend :)

https://automags.org/forums/showthrea...ONS-of-GOODIES!!!

modded frame now for sale...

If anyone needs tips for this mod message me and i will gladly help out

I went a different route with my mod, little more work than I had originally intended though

http://i33.photobucket.com/albums/d7...140112_003.jpg