Results 1 to 17 of 17

Thread: Devil mag 2 shots or full auto

  1. #1

    Devil mag 2 shots or full auto

    Name:  2015-10-04 09.04.34.jpg
Views: 54
Size:  85.9 KBTrying to build the Devilmag here. ULT + SHP Ninja tank.

    It either fires 2 shots or goes full auto.

    Any suggestions.

  2. #2
    Join Date
    Oct 2004
    Location
    Mt. Pleasant, SC
    Posts
    2,738
    take some shims out of your ult.

  3. #3
    I took all the shims out. It's still doing it. Double shooting, then full-auto.

  4. #4
    Join Date
    Nov 2001
    Location
    DeWitt, MI
    Posts
    782
    Let's determine if it's the electronic frame or the rest of the marker. Put a mechanical trigger frame on the marker. Does it still have issues?
    Last of the Salzburg Clan

  5. #5
    Join Date
    May 2014
    Location
    NJ
    Posts
    65
    Those have morlock predator boards in them right? Have you tried different fireing modes?

  6. #6
    Join Date
    Feb 2005
    Location
    Texas
    Posts
    9,305
    Step #1 - stop using the SHP tank and use one that the output is 850.

    Step #2 - set your ROF to 15bps
    Step#3 - set your fire mode to SEMI
    Step #4 - set you DEBOUNCE to 10 or higher
    Step #5 set your dwell between 6 and 10.

  7. #7
    Join Date
    Feb 2005
    Location
    Texas
    Posts
    9,305
    I take that back - STEP #1 try a stock body first. Then go to the next step.

  8. #8
    Thanks guys. I don't have air in my 850 output tanks right now, so I'll have to wait until I can get lower air.

    I was wondering if the SHP is making the ULT go nuts.

  9. #9
    Join Date
    Nov 2013
    Location
    Austria
    Posts
    441
    Hi there - as the previous owner of that frame and having also used it with SHP and standard setups I can confirm that it will in fact tend to go full auto with an SHP.
    Standard works perfectly in any mode.

    Apart from that what BigEvil posted is spot on:
    "Step #1 - stop using the SHP tank and use one that the output is 850.

    Step #2 - set your ROF to 15bps
    Step#3 - set your fire mode to SEMI
    Step #4 - set you DEBOUNCE to 10 or higher
    Step #5 set your dwell between 6 and 10."

    I sent it to you with an ROF of 15 bps and debounce and dwell didn't cause any issues when I had it either - so I would recommend trying to use a standard setup/tank with 850 psi first before changing other settings.

    BTW - I also have one of those XMT carbon bodies - worked fine with it - no issues whatsoever.
    I did, however, use a Rail with an RT sear and not an AM/MM type - that probably helps also.

    Once you get it working you'll have a lot of fun with that thing!
    Last edited by flampaint; 10-06-2015 at 12:45 AM.

  10. #10
    Ha ha. My 400 PSI SLP Ninja tanks shoots exactly the same what as the SHP. So, I'll try to switch out the rail now.

    Could a bad sear be causing such a thing? What does a bad sear look like?

  11. #11
    Join Date
    Nov 2001
    Location
    DeWitt, MI
    Posts
    782
    Rounded edge instead of sharp point.

  12. #12
    Join Date
    May 2013
    Location
    NOVA
    Posts
    406
    Is that an RPG Chimera frame thats being used?

  13. #13
    Join Date
    Sep 2002
    Location
    Live Free or Die
    Posts
    2,330
    Quote Originally Posted by Zeropjc View Post
    Is that an RPG Chimera frame thats being used?
    Yup, DevilsDen (I believe that was the shops name, its been awhile) used RPG Chimera slugs to make some of the Devilmag frames. He also used Hyperframes for some.
    Quote Originally Posted by dano_____ View Post
    I keep forgetting to not feed my mags after midnight so they seem to multiply regularly.

  14. #14
    Fixed. Board was left in programming mode. I needed my magnifier glasses to see the tiny toggle switches. This thing ripps now. Thank you everyone. Not sure why you even need eyes. Shot a whole hopper of boiled crappy paint in the garage, didn't break one ball out of a gravity feed hopper. That level 10 is amazing.

  15. #15
    Join Date
    Nov 2013
    Location
    Austria
    Posts
    441
    Quote Originally Posted by djinnform View Post
    Fixed. Board was left in programming mode.
    Glad to hear it's working now. Did you get it from me with the toggle switches left in programming mode?? Would be strange though, since I never had any issues when switching between firing modes and other settings - it would always operate without any issues and I sued it quite a bit
    Last edited by flampaint; 10-09-2015 at 03:16 AM.

  16. #16
    Quote Originally Posted by flampaint View Post
    Glad to hear it's working now. Did you get it from me with the toggle switches left in programming mode?? Would be strange though, since I never had any issues when switching between firing modes and other settings - it would always operate without any issues and I sued it quite a bit
    Yeah weird. It was in programming mode for sure. I needed a microscope to see the tiny switches and a razor prong to switch the switches. I love it. But, it didn't work with the RT sear. It only works with the AM/MM sear.

  17. #17
    Join Date
    Nov 2013
    Location
    Austria
    Posts
    441
    That is very strange... well, the important thing now is that you got it to work with your setup.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •