Results 1 to 7 of 7

Thread: RPC E/X-Mag Boards

  1. #1
    Join Date
    Aug 2003
    Location
    www.BigEvilOnline.com
    Posts
    2,580

    RPC E/X-Mag Boards

    REFLEX PAINTBALL CUSTOMS
    E-Mag/X-Mag Board

    DO NOT PM ME WITH AN ORDER REQUEST, IT WILL BE IGNORED!!!!
    EMAIL ME!!!!!!! JJAI@COMCAST.NET


    This is a completely new board that will replace the no longer available OEM boards

    The board is a “drop in replacement” product (take the old one out, drop the new one in. Save all your old electronic parts.NO SOLDERING!!!!)

    We made some changes to the current design to make it more up to date

    The New Main Board Supports the following features:

    Break Beam/Bounce Beam Eye Systems
    New HES trigger
    Use the rear button as a power switch
    Use the rear button as a mode/eye switch
    Multi-color LED (no LED Screen)
    AUX/Warp Feed Port
    Solenoid Port (you can unplug your solenoid)
    Power Port (you can unplug your power cable)
    Solenoid Polarity Correction


    The R.P.C. E/X-Mag Boards come pre-loaded with our Reflex 7.0 software.
    Reflex 7.0 Code supports:
    (13) Fire modes = Semi (uncapped), Semi (capped), Auto Response, "Mild Ramp", "Max Ramp", "Z-Burst", Full Auto, CFOA, Millenium, PSP Auto Response, PSP Ramp, PSP Burst, NXL
    Adjustable Trigger Debounce (checks trigger noise levels)
    Adjustable Dwell (adjustment for your solenoid)
    Adjustable Anti-Bolt Stick (adjustment for the bolt system)
    Adjustable Ramp Rate (percentage of how fast to get to ramping modes)
    Adjustable Ramp Start BPS (how fast you have to ACTUALLY shoot in order to start ramping)
    MROF (the max rate of fire your marker will shoot when the board is turned on)
    Adjustable Burst Value (works with "Z-burst" and "PSP Z-Burst". Changes the number of shots)
    Eye Off ROF (the rate of fire you can get when the eyes are dirty or malfunctioning)
    Eye Type (Break Beam or Reflective/ACE)
    Adjustable Mechanical Debounce (checks marker noise levels)
    Reset to Factory Defaults

    When you Purchase a New Board it comes with:

    (1) New R.P.C. E/X-Mag Main Board with Reflex 7.0 software
    (1) New Power Cable (connects your battery to your board)
    (1) New HES (the trigger switch)
    (1) New Solenoid Coil (connects to your new board with connectors so you can remove it)


    We have set a price of $205 (shipping and insurance included)

    How to Purchase:
    [B]Contact me via EMAIL. JJAI@COMCAST.NET
    Payment in the form of "Personal - Gift" via Paypal ONLY

    32 boards remain for sale (as of 12/31/2015):
    Purchase & Shipping Information: (copy this into your EMAIL AND YOUR PAYPAL NOTES and fill the information out)
    Your AO Name:
    Your First and Last Name:
    Your Paypal Shipping Address (the address on your paypal account where you have items sent to)
    Your Shipping Address (the address we are sending the board to; can be different than the address above)
    Your Phone Number (xxx-xxx-xxxx)
    Your Paypal E-Mail Address (the one registered with Paypal)
    Your E-Mail Address (if different from the paypal e-mail address)
    Payment(s) Sent: (we would like the buyer as well as us keeping track of all payments sent to avoid any confusion; include amounts and dates)
    Payment Form: Payments MUST be sent as a "Personal - Gift" to: jjai@comcast.net



    Reflex Paintball Cutsoms E/X-Mag Board Installation Guide/Manual


    WARRANTY-
    Against all manufacturing defects. Each board is tested prior to shipping in an AGD frame with an AGD battery pack. Warranty will extend 30 days from the date of shipping.
    Last edited by p8ntbal4me; 01-20-2016 at 08:36 PM.

  2. #2
    Join Date
    Dec 2004
    Location
    Jeet yet ?
    Posts
    8,132
    Looks good !

    Last edited by going_home; 12-29-2015 at 04:07 PM.

  3. #3
    Join Date
    Jun 2003
    Posts
    7
    Is there limited quantities of boards?
    some people run, some people hide, I prefer Rambo style

  4. #4
    Join Date
    Aug 2003
    Location
    www.BigEvilOnline.com
    Posts
    2,580
    Yes. Less than 40 remain

  5. #5
    Join Date
    Nov 2002
    Location
    Washington State
    Posts
    380
    Mine arrived yesterday, shipping was very fast, and installation was straightforward.

    Installed today and the board powered right up, the only problem I encountered was due to gun setup. Mech mode was fine, but it wouldn't fire in e-mode.

    p8ntbal4me walked me through troubleshooting to ensure it wasn't a board problem and then moved on to checking for mechanical faults. He had me check and adjust the trigger rod and plunger lengths, as well as make sure the sear wasn't binding. Once this was done, the gun worked fine in mech mode, e-mode, and hybrid with no issues.

    There was no issue with the board, but he took the time to assist me with mechanical adjustment problems. The assistance was greatly appreciated...

    Thanks again!


    Walker
    O.F.P.P.A. - OLD FARTS PAINTBALL PLAYERS ASSOCIATION
    When you wrap-up the day with beer and Bengay.

  6. #6
    Join Date
    Aug 2003
    Location
    www.BigEvilOnline.com
    Posts
    2,580
    Glad we could figure the problem out over the phone!

    Anyone that has issues, please email me.

  7. #7
    Join Date
    Dec 2009
    Location
    Austin, TX
    Posts
    321
    I couldn't resist, I purchased one of these for my xmag project!

    Jai shipped super fast and install was a peice of cake with the help of Bigevil online tutorial. I slapped my warpfeed on and shot a hopper last night, I was shooting ropes! I didn't even mess with the settings left them as they came in the package.

    I can't wait to get this thing on the field tomorrow.

    I made it to the field this past Saturday and this board worked amazing! Awesome work Jai!
    Last edited by Stedspitcher; 04-12-2016 at 06:34 PM.

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •