Want: Classic RT Hard Line Setup

[going_home]

And good condition black classic RT sight rail and foregrip bracket.

Lmk

[Cyco-Dude]

tunaman might have some hardlines left.

[Spider-TW]

Dust or gloss? I think I have a decent condition dust black.

And you need screws too?

I think my parts got separated into different boxes.

[vintage]

tunaman might have some hardlines left.

thats where i got my last one.

[Cyco-Dude]

Dust or gloss?

rt classics are dust black. the gloss black sight rail was for the emag.

[going_home]

Dust.

Bob says hardlines are gone for good.

Thus this thread.

[Spider-TW]

I'll dig tonight.

[Spider-TW]

I found the dust sight rail. It has several small ano dings around the edges. I think I can find a full set of screws.

However, the foregrip mount I found was an RT pro, black coated steel. I figured out the dust one is still on my RT.

I guess you're still looking for a full set, but pm me if you need just a sight rail.

[Cyco-Dude]

Bob says hardlines are gone for good

i'll see about that...

[going_home]

i'll see about that...

Thanks

[BigEvil]

I can whip you up some 3k psi custom line using macro fitting...

[rawbutter]

I can whip you up some 3k psi custom line using macro fitting...

That's cool. Does any hard-line fit into macro fittings, or did you have to modify it somehow?

[going_home]

Does that work with these :

http://store.azodin.com/index.php?ro...arch=macroline





or only with the nordgren fittings you have pictured ?

[BigEvil]

as long as they work with standard 1/4" macro line it should work with this stuff. It's 1/4" 3k rated aluminum. And it's anodizable.

[Cyco-Dude]

if it's not for an rt classic, i do have a couple of venom hardlines. they would be a lot easier to work with on a non-rtc setup, as you could easily disconnect the line to service the valve, etc.

also, the 1/4" tubing with macroline fittings would also work well. people have done that before, and maggot even made a few up in black anno that worked great.

[going_home]

For a classic RT

[going_home]

as long as they work with standard 1/4" macro line it should work with this stuff. It's 1/4" 3k rated aluminum. And it's anodizable.

Ok, for a classic RT, need one.

I have no way to bend it without crimping it.......

[Tunaman]

Ok, for a classic RT, need one.

I have no way to bend it without crimping it.......

fill it with sand and bend it

[BigEvil]

fill it with sand and bend it

Or go to Harbor Freight and spend the $8 for the tools you need to cut and bend it

[going_home]

Or go to Harbor Freight and spend the $8 for the tools you need to cut and bend it

Ok theres one within close proximate.

Where do I get the line ?

And what do I need to get at the chinese junk tool store ?

[Cyco-Dude]

tubing bender. if you plan you use macroline fittings, get 1/4" OD tubing of your choice. if you want to use the compression fittings that come on rt classic, get 3/16" OD tubing. there are places online to order it.

or gimme a few days and i'll see if i can just get the real deal. i've got top men on the job...top men.

[BigEvil]

I have 10' of it here. I'll whip some up for whoever wants it.

[BigEvil]

If anyone is interested PM me

[going_home]

Still looking for a black classic RT sight rail and foregrip bracket.