Let me first say, this is a workhorse, not a beauty pageant winner.....so dont rag on it for being a little beat up. 
This is actually the second incarnation of this EP mag. First attempt was about 4 years ago(right as the ULT came out). It used a basic stamp and a giant noid that needed 12 volt. It worked great then, but it needed an external battery. So I scrapped it....and tried the ULT instead.
But now it is back.....
Other side:
Reg cover off, electrical tape is there to pinch the line against the reg. LP line goes up through the RT foregrip, and into the rail, then back into the grip....completely hidden:
Up close of the switch.....extra hole is from my initial location, but the trigger was too soft and didnt have enough return force. Where its at now is by far the best feeling trigger ive ever used:
Now for the money shot.....internals:
My 3 way adjustable trigger(pre, post, activation point) you can also see the switch a little:
Yes, I realize thats not an AGD screw....mine is too short for the ULE body and RT rail....happened to have that one handy and I'm too cheap to pay shipping for 1 screw.
The only real external way to tell its not a normal mag:
On/off switch is a membrane pad located under the H at the bottom of the grip, the eye switch is a membrane pad located under the H at the top of the grip. I'm amazed ive never seen anyone else do this because it works GREAT. Nothing has ever accidently turned it on....it takes deliberate pressure right at the corners of the grips to depress the membrane.
Eyes are coming.....probably making the eye holder/cover tomorrow if theres time.
Only tools really used were a drill press, dremel, hacksaw, file, and taps. I have access to a mill, but the dremel was much easier for all the test fitting.
Anyhow, just thought Id show off my little project.....cant wait till the it gets nicer out to use it again. I'll snap some more pics after the eyes are finished.
This is actually the second incarnation of this EP mag. First attempt was about 4 years ago(right as the ULT came out). It used a basic stamp and a giant noid that needed 12 volt. It worked great then, but it needed an external battery. So I scrapped it....and tried the ULT instead.
But now it is back.....
Other side:
Reg cover off, electrical tape is there to pinch the line against the reg. LP line goes up through the RT foregrip, and into the rail, then back into the grip....completely hidden:
Up close of the switch.....extra hole is from my initial location, but the trigger was too soft and didnt have enough return force. Where its at now is by far the best feeling trigger ive ever used:
Now for the money shot.....internals:
My 3 way adjustable trigger(pre, post, activation point) you can also see the switch a little:
Yes, I realize thats not an AGD screw....mine is too short for the ULE body and RT rail....happened to have that one handy and I'm too cheap to pay shipping for 1 screw.
The only real external way to tell its not a normal mag:
On/off switch is a membrane pad located under the H at the bottom of the grip, the eye switch is a membrane pad located under the H at the top of the grip. I'm amazed ive never seen anyone else do this because it works GREAT. Nothing has ever accidently turned it on....it takes deliberate pressure right at the corners of the grips to depress the membrane.
Eyes are coming.....probably making the eye holder/cover tomorrow if theres time.
Only tools really used were a drill press, dremel, hacksaw, file, and taps. I have access to a mill, but the dremel was much easier for all the test fitting.
Anyhow, just thought Id show off my little project.....cant wait till the it gets nicer out to use it again. I'll snap some more pics after the eyes are finished.
I think the rail and foregrip are the parts that make it look bad...other than that I dont think its that horrible. Theres some kind of epoxy on the foregrip, nothing will take it off.
lol 
Comment