Fresh pics of the Demonic Impy

[PsychoMag]

Here are some pics of the Demonic Impulse...
This is the stock Demonic Vision Impulse from Roughneck Paintball.
After all the changes made by us, because of all the good and bad feedback from you the players that was greatly appreciated, this is what we came up with, and we are very happy with what we turned out with.

Demonic Milling.....................15 oz lighter than stock Impulse

Demonic Ano.........................Blood Red to Black fade with a textured Satan finish

Barrel....................................All American back with matching ano freak front, made
to be interchangeable with Freak
kit

Delrin Internals:
Bolt..................Demonic Roar Impulse bolt w/ Roar pin Valve................Demonic Portal Valve
All friction free internals mod. cause the gun to operate @ 120psi-150psi

Titanium Internals:
Hammer...........Demonic Black Hole Hammer Piston..............Demonic Rammer Piston
All Titanium internals add to lowering operating pressure and increase the cycle rate

Trigger Frame..........................set screws for pretravel mounted into frame and
adjusts to become as light as
an Angel

Front Cap................................Demonic Delusion front cap

Feedtube.................................Demonic Inferno feedtube

Double Detent.........................accuracy, no cross spin

Vision Board...........................no chopped balls, adjustable, shoots black paint

[PsychoMag]

another pic

heres another

[PsychoMag]

and yet another

and another

[gimp]

Very cool. I think the black part of the barrel looks to shiney compared to the rest of the gun.

[Phil]

Dont know if you are looking for feedback or just praise but here goes. The impulse is a fantastic gun! The four things that bother me about it you failed to address. Since your not making the gun specifically for me I didnt expect you to but here is my two cents. The stock trigger is too sloppy. The pressure gage on the gun is too big. The crappy dwell cover sucks! The on/off switch is really wimpy. These are all minor but they really bother me. Otherwise you have a kool gun there.

[shartley]

I agree with all comments thus far posted.

Not a bad looking marker..... but did I mention before that I thought they looked a bit "stubby"?

[Bartleby]

very true. i too agree with all the comments thus far. yet, i don't know what your intentions are with this gun. are you planing on selling these or maybe just a few or what? and if you are planning on selling a given number, how much are you going to charge? i have three friends that are saving up for impulses but their only drawback to getting one is the weight. 15oz is a hell of a lot and i'm sure they'd be interested.

[manike]

It's a nice gun. I had the pleasure of getting my grubby hands on one at the cup.

The only thing I don't like is that cut down 'triple' stack guns like the impy or BM2K tend to look very 'hunchbacked' and kinda ugly.

Shoots nice though and is much lighter.

manike

[MikeCouves]

Have you seen the TKO Implulses that are on special at PBALLGEAR.com? Here's a pic of them:



Strange resemblance .

[manike]

They need to cut that bolt down...

Nice guns. If I remember correctly Aaron Stephens at Smart Parts is responsible for the custom signature gun range. He's doing some nice stuff.

manike

[PsychoMag]

This marker is made by Tez of Demonic Paintball. It is maketed to be widespread. Several companies are already on the bandwagon to sell them. As far as the trigger goes, there is a $49 upgrade for what is called the Devil's Finger trigger which adds the ability to sidetap the trigger from either side. There are also multiple available feednecks, and a matching Freak kit.

The Vision Impys will be $949
and the non Vision are about $800

you can get them from

https://www.RoughneckPaintball.com

[manike]

Does Tez actually do the machining or does SP do it for him to his design?...

manike

[PsychoMag]

Tez machined the first one, and designed the internals which are all delrin and titanium, but SP does the production of it for warranty purposes and cost effectiveness. They are in the process of developing an all titanium Freak kit for SP which will include ti sleeves.

He has a cocker due out next(December). then a shocker(february). and now in the works for an Angel

[thei3ug]

Not to say I plan on it... but if I send roughneck a list of parts to swap out, would they assemble one for me to my specs?

[PsychoMag]

Originally posted by thei3ug
Not to say I plan on it... but if I send roughneck a list of parts to swap out, would they assemble one for me to my specs?

Tez will do custom conversions and add the stuff you want, but certain parts must be used in conjunction with the milled body.

Contact Him